LINKSYS wrt54gl

Po prvnim prihlaseni (telnetem) je treba si ined zmenit heslo (passwd), rebootnout AP a prihlasit se pres ssh (telnet se pak automaticky zablokuje).

---

• Predelani linksyse na router co ma 5 sitovych ethernet karet (wifi zustava jedno)
  • Nastaveni 5ti sitovek na jednotlive porty switche (vcetne WAN)

<bash> nvram set vlan0_ports="1 5*" nvram set vlan0_hwname="et0" nvram set vlan1_ports="4 5*" nvram set vlan1_hwname="et0" nvram set vlan2_ports="2 5*" nvram set vlan2_hwname="et0" nvram set vlan3_ports="3 5*" nvram set vlan3_hwname="et0" nvram set vlan4_ports="0 5*" nvram set vlan4_hwname="et0" nvram commit reboot

1. Nastaveni portu 1 pro vlan0 je vyzadovano pro budouci mozny upgrade firmware.
2. Upgrade fw nejde kdyz neni port 1 ve vlan0.

</bash>

Pak bude toto rozdeleni
vlan0-> port3
vlan1-> wanport(internet)
vlan2-> port2
vlan3-> port1
vlan4-> port4

• • Aktivace zbyvajicich vlanu (defaultni jsou aktivni jen vlan0 a 1) je nutno provadet uz skriptem po kazdem bootu:

<bash> vconfig add eth0 2 #Pridat vlan2 k eth0 vconfig add eth0 3 #Pridat vlan3 k eth0 vconfig add eth0 4 #Pridat vlan4 k eth0

ifconfig vlan2 hw ether XX:XX:XX:XX:XX:02 #Nastavit mac adresu pro vlan2 ifconfig vlan3 hw ether XX:XX:XX:XX:XX:03 #Nastavit mac adresu pro vlan3 ifconfig vlan4 hw ether XX:XX:XX:XX:XX:04 #Nastavit mac adresu pro vlan4

ifconfig vlan0 xx.xx.xx.xx netmask xx.xx.xx.xx broadcast xx.xx.xx.xx up #Nastavit IP adresu pro vlan0 ifconfig vlan1 xx.xx.xx.xx netmask xx.xx.xx.xx broadcast xx.xx.xx.xx up #Nastavit IP adresu pro vlan1 ifconfig vlan2 xx.xx.xx.xx netmask xx.xx.xx.xx broadcast xx.xx.xx.xx up #Nastavit IP adresu pro vlan2 ifconfig vlan3 xx.xx.xx.xx netmask xx.xx.xx.xx broadcast xx.xx.xx.xx up #Nastavit IP adresu pro vlan3 ifconfig vlan4 xx.xx.xx.xx netmask xx.xx.xx.xx broadcast xx.xx.xx.xx up #Nastavit IP adresu pro vlan4 </bash>

• Nastaveni FD / HD / 10 / 100 pro jednotlive porty
  • Pro nastavovani jednotlivych vystupu, je treba nainstalovat balik robocfg
  • ipkg update
  • nasledovne na www kliknout na install u prislusneho baliku

<bash> robocfg show #Zobrazit aktualni konfiguraci vsech portu robocfg port X media <auto|10HD|10FD|100HD|100FD> #Nastaveni modu portu robocfg port X mdi-x <auto|on|off> #Nastaveni Auto-Cross </bash>

• Drobne stripky z testovani HWAP Linksys:

BusyBox v1.00 (2005.11.23-21:46+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
 _______                     ________        __
|       |.-----.-----.-----.|  |  |  |.----.|  |_
|   -   ||  _  |  -__|     ||  |  |  ||   _||   _|
|_______||   __|_____|__|__||________||__|  |____|
         |__| W I R E L E S S   F R E E D O M
WHITE RUSSIAN (RC4) -------------------------------
 * 2 oz Vodka   Mix the Vodka and Kahlua together
 * 1 oz Kahlua  over ice, then float the cream or
 * 1/2oz cream  milk on the top.
---------------------------------------------------
root@OpenWrt:~#

root@OpenWrt:~# df
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/root                 3264      1884      1380  58% /
none                      7188        12      7176   0% /tmp

root@OpenWrt:/etc/quagga# free
             total         used         free       shared      buffers
 Mem:        14376         9136         5240            0            0
Swap:            0            0            0
Total:        14376         9136         5240